基于多材质复合管柱的裸眼井壁支撑工艺及应用

已完钻超深裸眼水平井侧钻技术是经济、高效开发油藏剩余油的主要手段之一，传统的磨铣钢套管开窗侧钻技术存在下入摩阻大、磨铣耗时长导致开窗失败等问题。为此，提出了基于多材质复合管柱的超深水平井裸眼井壁支撑工艺，结合中国西北油田已完钻超深裸眼水平井井况，首先，提出了基于“铝合金+碳钢”的多材质复合管柱组合及设计方法；其次，开展了基于管柱实物屈曲实验数据的管柱临界屈曲载荷计算模型适用性评价，并优选出了适合于“铝合金+碳钢”多材质复合管柱的屈曲临界载荷计算模型；最后，研究了综合考虑管柱扭矩、摩阻、刚性、井眼条件、管柱强度及材质的多材质复合管柱下入性分析方法，并利用下入性分析软件对西北油田顺北X1井、X2井、X3井、X4井复合管柱进行了下入可行性评价。该方法在X1井和X2井得到成功应用，进一步论证了该工艺现场应用的可行性。研究成果可为超深水平井裸眼井壁支撑的复合管柱设计和下入可行性评价提供理论参考。     

数据驱动的铝基复合材料性能预测和逆向设计

采用数据驱动的方法对 SiCp(0.5CNT)/7075Al 铝基复合材料的化学成分以及制备工艺进行了分析, 针对抗拉强度和延伸率两个力学性能进行了特征重要性分析, 构建了包含 8 种机器学习算法的集成框架, 自动进行模型的参数调优和最优模型选择, 并在此基础上进行了材料逆向设计. 实验结果表明, 在 470 ${^\circ}$C 固溶 40 min, 120${^\circ}$C 时效 15 h 的热处理工艺下, SiCp(0.5CNT)/7075Al-1.0Mg 复合材料抗拉强度和延伸率的预测值为 617.48 MPa 和 2.98%, 实验值为 647.0 MPa 和 3.31%, 两项物理性能的平均绝对百分比误差(mean absolute percentage errors, MAPE)较小, 依次为 4.56% 和 9.97%. 这说明本数据驱动方法对铝基复合材料的工艺优化和性能提升有一定指导意义.     

Effect of Al on microstructure and mechanical properties of as-extruded Mg–1Mn alloy sheet

The effect of Al addition on microstructure and mechanical properties of hot extruded Mg–1 Mn alloy sheet was investigated. The results revealed that the dynamic recrystallization was promoted by increasing Al content. The ultimate tensile strength and yield strength of the alloy increased with the increase of Al content. The Mg–9 Al–1 Mn alloy exhibited the highest strength, with tensile strength of 308 MPa, 307 MPa, 319 MPa, yield strength of 199 MPa, 207 MPa, 220 MPa and the elongation of 20.9%, 20.1%, 19.2% in 0°, 45°, 90°, respectively.The high strength was mainly attributed to the formation of fine dynamically recrystallized grains and large amounts of the second phase. The strengthening mechanism of the alloys was explained.     

Microstructure,mechanical properties and wear resistance of an Al–Mg–Si alloy produced by equal channel angular pressing

Microstructure, mechanical properties and wear resistance in an ultrafine-grained Al–Mg–Si alloy fabricated utilizing a combination of equal channel angular pressing (ECAP) and dynamic aging were investigated in this paper. The results indicated that the grain size of the ECAP alloy was significantly refined, i.e., to ~239 nm after three ECAP passes. Meanwhile, the yield and tensile strength of the ECAPed material reached 340 MPa and 445 MPa, respectively, while maintaining a significant uniform elongation of 14%. Wear resistance results demonstrated that the wear rate, wear depth and width of the ECAPed material decreased in comparison with the solution-treated (SST) and peak-aged (T6) conditions under a load range of 5–25 N. The adhesive wear that occurs in the undeformed specimens at 10 N does not appear in the ECAPed specimen at the same load, indicating that the ECAPed specimen delay the appearance of more serious wear mechanisms under certain loads. The cooperative interaction of high density nano-scale β" precipitates and dislocations resulted in a combination of super-high strength and good work hardening ability which suppressed the extension of cracks between the friction layer and the plastic deformation zone. As a consequence, the combination of ECAP and dynamic aging brings a significant improvement for antifriction performance of the 6061 aluminum alloy.     

Effect of heat treatment on microstructures and properties of a novel Al-Zn-Mg-Cu alloy for oil drilling

In view of the special requirements for strength, heat resistance and corrosion resistance of Al-Zn-Mg-Cu alloy for oil drilling, the Al-6.2 Zn-2.5 Mg-1.6 Cu alloy was prepared by increasing Cu content on basis of Russian Series 1953 alloy. The effect of heat treatment on the microstructures and properties of the alloy was characterized by optical microscope(OM), scanning electron microscope(SEM) and transmission electron microscope(TEM), and investigated by tensile test at room temperature, thermal exposure test and corrosion test. The results show that the strength after T6 aging treatment exhibit a decrease trend as an increase of the solution temperature from465 °C to 480 °C. After the solution treated by the rate of 470 °C/1 h, second phases dissolve into the matrix very well and the strength property reaches optimum. The alloy has better comprehensive properties treated by a solution treatment of 470 °C/1 h and then followed by an aging treatment of 120 °C/24 h + 170 °C/1 h + 120 °C/24 h. Under the aging state, the precipitated phases inside the grains are suitable in size, while on the grain boundary distribute discontinuously and the precipitate-free zone is obvious. Besides, the alloy still maintain high tensile properties. The yield strength, tensile strength and elongation are 650 MPa, 686 MPa,12.0%, respectively. The yield strength retention after heat exposure is 92%. The alloy has good corrosion resistance and the exfoliation corrosion degree. The average corrosion rate in the H_2S and CO_2 environment is 0.0024 mm/a, which is far less than the required 0.12 mm/a. It is insensitive to H_2S and CO_2 environments.     

基于修正斜压场的RC框架边节点剪切性能分析

为研究钢筋屈服强度和混凝土抗压强度对钢筋混凝土(RC)框架边节点剪切性能的影响规律,基于修正斜压场理论(MCFT),对某框架边节点的剪切应力-应变骨架曲线进行数值模拟,并与试验结果进行对比.在验证MCFT算法的精度后,研究钢筋屈服强度和混凝土抗压强度两个参数变化对RC框架边节点剪切应力-应变骨架曲线和峰值剪切应力的影响规律.结果表明:基于MCFT可以较好地模拟RC框架边节点的剪切应力-应变关系曲线; RC框架边节点的峰值剪切应力对混凝土抗压强度的变化更为敏感,但当试件的钢筋(HRB400)屈服应力下降幅度超过16.45%时,对钢筋屈服应力的变化更为敏感;当试件的钢筋(HRB400)屈服应力下降幅度超过10%时,节点发生钢筋滑移破坏,此时峰值剪切应力会大幅下降.     

激光快速成型TC4合金显微组织及力学性能

采用金相显微镜、扫描电镜、电子拉伸机等，研究了激光快速成型TC4合金沉积态在平行沉积方向和垂直沉积方向的组织和力学性能.结果表明:激光快速成型TC4合金沉积态宏观组织沿沉积方向生长的粗大β柱状晶呈明暗相间的条带状结构，具备典型的魏氏组织特征;垂直沉积方向的强度比平行沉积方向的强度高，但塑性低;合金断口为韧窝状断口，垂直沉积方向的断口韧窝尺寸比平行沉积方向的小.     

基于联合违约概率的资产组合投资优化方法

投资组合的资产联合违约概率(joint,probability of default,JPoD)是一种有效的系统风险测度工具.基于JPoD分析,提出了一种新的资产组合选择优化方法,即通过计算资产池中每两种资产的JPoD值得到JPoD矩阵,利用遍历算法逐次筛选,得出具有最小系统风险的多资产组合.实证分析首先利用2014 2015年的上证综指和深证成指数据验证了JPoD方法的有效性;其次,分别利用中国股票市场数据和美国股票市场数据将所提出的资产组合选择方法与马科维茨均值-方差组合理论、随机组合方法进行比较,结果表明无论是在中国股票市场还是美国股票市场,JPoD方法都明显优于其他两种方法.     

运用试验设计法优化某军品压铸弹尾工艺

根据某军品部件出现的问题，应用试验设计法成功地找出了最优组合，提高了该部件的强度，解决了该强度问题，使生产得以正常进行。     

浅析中国铝锭产能迅速扩充的原因

文章阐述了我国铝锭产能迅速扩充的原因。